How To Repair Chain Link Gate

Download Article

Chain link fences often sustain small-scale damage from bad weather and falling droppings, but this is something you tin set on your own. To fix a bad track, start by purchasing and cut a replacement rail. Once you've installed the runway, tie the mesh in place with pliers and wire ties. You tin can use the pliers to install a mesh or fix smaller areas past weaving in new strands. Utilize a come-along tool to tighten the meshing and continue your fence stiff.

1

Measure the diameter of the old rails. Hold a tape measurement against the ends of the rails you wish to replace. Note the pipage's diameter and then you can lodge properly-sized replacements.
two
Purchase new rail from a home improvement shop. Become rails the same size as your old ones. If part of your rail is loose or cleaved, you can bring it to the store then the employees can help you find a matching runway.
- The rail should have 1 tapered cease and one wider end.
Advertisement
3

Remove the wire ties on the fence'southward top rail. The ties connect the elevation of the chain mesh to the rail. Put on a pair of gloves and use pliers to bend the ends of the ties. Pull the ties through the chain links to costless the rail. Remove all the ties on the office of the rails yous need to replace.
iv

Measure and marker the new runway for cutting. Get someone else to help you concord the old rail upwardly to the new one. Slide the smaller, tapered end over the old rail, making certain the back stop of the tapered department lines up with the damaged part yous want to cut. Employ a pencil to marker this on the old rail, then mark the rail's other end.^[1]
5
Put on safety gear earlier cut the rail. Become some protective polycarbonate eyeglasses to protect you lot from metallic fragments when cut the rail. Also put on a respirator mask to avoid breathing in metal dust.^[2]
- If you lot're going to utilise a reciprocal saw, it'due south recommended that y'all also vesture hearing protection.
6
Cutting the damaged rail with a hacksaw. ^[iii] Find the line you marked earlier on the old rail. Saw into it to sever the track at 1 cease. Cut the track off at the other terminate to free it. Slide the old rails off and gear up it aside.^[4]
- Yous may employ a reciprocal saw, just take a friend agree the rail in identify as you cut it.
7

Unbolt the top rail from the corner mail to give yourself more room. Go to the corner post on the side where you'll install the tapered terminate of the new rail. Use an adjustable wrench or ratchet wrench to remove the carriage bolts on the tension bands. Slide the rail towards the mail to move information technology.^[5]
8

Lay the new rail in identify. Outset, slide the larger end of the track onto the smaller stop of the old rail. And so slide the tapered stop of the new rail into the rail you unbolted. You may need to saw the new rail a little bit to get information technology to fit perfectly.^{[half dozen]}
9
Reconnect the rails and wire ties. Slide the rails back into place, then supplant the wagon bolts to secure the corner bolt in place. Using pliers, loop the sometime wire ties around the runway and through the concatenation links to secure the mesh to the rail. The wire ties should exist placed every 24 in (61 cm) along the top rail.^[7]
- If you demand to replace the wire ties, purchase metal wire ties or nylon cable ties at a domicile improvement shop.
10

Repeat the process to supervene upon the bottom rail. If your fence has a bottom rail, it is repaired the same mode as the top rail. This time, loosen the corner post's lower tension band, and so remove the wire ties from the bottom of the argue. Measure, cutting, and install the new rail like you lot did before.

Advertisement

1
Use pliers to detach the superlative track's wire ties. Locate the wire ties connecting the mesh to the top rail. Wearing gloves to protect your easily, use your pliers to pull the ties through the chain links. This detaches the mesh from the rails. Pull the mesh dorsum from the runway, but don't remove it.^[8]
- If the wire ties aren't rusted or broken, set them aside and reuse them later.
2

Remove the lower wire ties to free the damaged wires. Commencement, observe the top ends of the damaged wires. They'll be wrapped around the undamaged wires, so pull them apart with the pliers. Follow the strands all the way downwards to the ground and utilize the pliers to also remove the lower wire ties.^[9]
3

Pull the wires upwards from the fence to remove them. ^[10] Take hold of the top ends of the damaged wires. Yous should be able to remove them by pulling them up off the debate. If they're still stuck, keep unraveling the concatenation links by twisting the damaged wires around the undamaged ones.
4
Cut the concatenation link textile to size. ^[11] If y'all're trying to fix a large area in the fence's meshing, purchase a curl of chain link fabric from a home comeback store. Mensurate out plenty of the material to embrace the gap. Untwist the wires at the end of the mesh department to remove information technology from the roll.
- If you lot're fixing a small area, you tin can use wires from an old fence
5
Weave the new wires into the fence. Hold the new mesh in place by tying it to the lesser bar with wire ties.^[12] To connect it to existing mesh, get a wire from the old fence or mesh roll. At the bottom runway, wrap the loose strand around the old mesh. Run the wire diagonally upwardly to wrap it around the new mesh. Go along doing this until reaching the top rail.^[13]
- The concatenation links should form a diamond pattern when y'all're finished. If yous're not trying to patch upward sometime meshing, you don't demand to practise this.
6
Tie the wire to the top runway. At the rails, loop the ends of the wires over each other. Pull the ends down towards the rail. Finish by applying wire or cable ties every 24 in (61 cm) along the runway to bind the wires to it.^[14]
- If your fence has a bottom rails, besides secure the lesser ends of the wires to it.
seven
Tighten the concatenation link mesh. To ready the mesh in place, makes sure the mesh is unbolted from the tension bands on the posts. Adhere a come-along tool to the 2 nearest posts. Crank the come-along tool until the chain links move no less than ⁱ⁄₄ in (0.64 cm) when you button them together with your fingers.
- Yous tin can go a come-along tool at a hardware shop.
Advertisement

Ask a Question

200 characters left

Include your email address to go a bulletin when this question is answered.

Submit

Advertising

It'south easier and less expensive to supervene upon damaged mesh with a gyre instead of individual wires.

Things You lot'll Need

Pliers
Hacksaw or reciprocating saw
Safety glasses
Hearing protection
Gloves
New rails
Wire ties

Mesh ringlet or wires
Wire ties
Pliers
Gloves

Almost This Article

Article Summary X

Repairing a chain-link argue is adequately directly-forward, and most fixes can be done on your own. To supervene upon the top or bottom rails, you'll demand to purchase a rail the same bore equally the old ones. Then, use pliers to remove the wire ties belongings the old rails, put the new track in place, then reconnect the rails with wire ties. If the new track is too long, yous tin can use a hacksaw to cut information technology to size. If y'all want to repair the concatenation mesh, you'll demand to cut the wire ties with pliers, take out the erstwhile sheet, so secure a new sheet of mesh to the rail. For more than communication on measuring your new debate pieces, read on!

Did this summary help y'all?

Thanks to all authors for creating a page that has been read 52,070 times.

Did this article assist you lot?